Видео

Hi. Have you had to deal with an error code 20c2? I'm getting this on my f5 on my f5. It won't tilt or elevate. Do you have any idea what I need to do to fix it

Hey Dan I just thought I would tell you that I have a volt pro charger sitting in my closet and I went back to my older grey and green one the one that was built like a tank compared to these newer volt pro ones because it did the same thing I don't know if my volt pro charger is the one with a switch for 8amp or 10amp mode I do know that it says it blinks the lights to a show which mode but I never seen any switch on the bottom it's atleast 18 to 24 months old but it Definitely cooked 1 of my new batteries at the time

Is the Amy the best I am looking forward to getting my Amy hybrid. The swing bearings in my old Sunrise have lasted forever

Hello Sir, i have a used permobile c350 that i bought recently, the batteries were empty so i tried to charge them directly with a victron charger, one them was charged but the second one as i started to charge it, about 5 min later it started to leak from one the six nuts (light leak) My question: is there any way to repair that nut or to close it with glue maybe if there's a crack on it, or can I continue to charge it even if it is leaking??? Is there a danger ? Thank you so much for your reply and your time. Have a nice day.

Same, I went through NSM and when we were about to make a complaint through their corporate office they magically started responding to our emails. My entire process lasted about two and 1/2 years. The guy is really nice, but I'm going through a different DME for my next chair. I love the new chair so far though.

I have a question can you get larger motors I have a friend that is round 450lb to 500lb the one I went and got was a jazzy 600 but it doesn't have enough power and they can't go very far

My dealer installed new 55ah MK Batteries in my 2023 Quantum Edge last week. Are better gel batteries available?

Have you seen the "rollerblade" wheels Quantum has that attach the footplates for pushing open doors without damage?

We want you to bake a cake in the next video 🎉😂🤣

Dan, I appreciate your videos and advice. I have another question. I've just put new 12 volt 18ah batteries in my little, backup Pride Go chair. I've fully charged it with the factory charger. How much should I discharge it the first few cycles?

I need aggressive tread 😮

Got my new Permobil M3 on Tuesday after 2 years of waiting. One thing I'm concerned about is it fitting in a mini van with a lift. It's very big and heavy. In your experience do you think it'll fit?

I like to use the acrylic paint pens for touch ups

Thank you very much for getting back👍

From where did you get the mudguard for the caster wheels? I don't have it.

hmm🤔

Whats the brand of tyres??? I would have solid tyres too painful

**UPDATE!** i went ahead and ordered 2 of the HANTEK 365F dataloggers from china for the volt pro battery testing - one for voltage and one for current - they are battery powered, and seem like a pretty useful bit of kit for future projects as well! they should be here in a few weeks, and i'll get to work gathering data on the charging cycles/voltage curves on these permobil chargers! ($319 later... YEESH!) lol

**UPDATE!** i went ahead and ordered 2 of the HANTEK 365F dataloggers from china for the volt pro battery testing - one for voltage and one for current - they are battery powered, and seem like a pretty useful bit of kit for future projects as well! they should be here in a few weeks, and i'll get to work gathering data on the charging cycles/voltage curves on these permobil chargers!

What about installing a heated and cooling seat? I love the vlogs, thank you.

Yes this is James set for Diamond Odessa Texas and this is the first time I've seen your channel and I was very interested I got a friend that I go to church with that is in a wheelchair and I've replaced his wheels for the bearings in us will several times he's got better issues and his charger shows that they're charged but he can't get no life out of them I mean he can't even go 5 minutes without him going dead

Hi, do you have any second-hand ones for sale?

Ug

Hello, do you know much about the quantum q-logic 3e and ex? I just got the quantum forfront 2 with the q-logic 3e my chair only had one actuator the seat lift. I want to go to the 3ex I bought one of of eBay but I heard that you need to program the joystick to run on the chair. Is it easy or what do you think?

👍🏾

@39:30 The first thing that came to my mind was Ferrari. Don’t know why, lol. Would be fun though, with Ferrari logo on the rims. Haha

love my lfp batteries:) 210ah and all of it usable with over 4000 cycle capable.

@8:50 Tip. If you have a problem with loose caps falling off, you can put a cable tie around the cap (the two ends) and the “arm”. That should hold them in place ;-)

Blimey Dan you are really inspiring, I wish that I was able to do the things that you do, getting old ain't much fun, only thing I managed to do lately was installing new 55Ah batteries in my quantum and that nearly seen me off, I'm over 70 now and boy do I feel it. Your chair looks brand new 👍

Hey Dan, I installed a set of the 3.50 “off road” tube tires on my outdoor F3. (Like you did in a previous video) I see a set of aggressive tread Permobil marked caster tires only, (no rim or bearing). How big of a deal is it to put new tires on original caster 1:59 rims? The F3 was made in 2020.

You're not just sharing your thoughts. But also your experience. No matter how well trained a technician is, without using a chair themself for an extended period of time, knowledge from experience trumps training in my opinion.

I was telling you to spin the battery, you just didn't listen...😂😂

Hey how are you? Really enjoyed your trip to soccer with your friends, had fun but sorry the van broke down twice, makes for a long trip. I wanted to tell you I purchased a late he thinks Nov 2023 Permobil m300 with every option available, had 7.5 miles total. Sadly she passed in Jan 2024, I am 5'9 she was 5'4 so been doing some adjustments, seat, arms etc done except to lengthen the arms, my wrist hits the end of the hand hold on the left, joy stick on the right. but I can't find a video on adjusting them forward and more importantly the seat back is way too low for my long body, my head can't lean back at all and the head rest when going to stand comes down and pushes hard on neck and shoulders so can't deal with that, it's very painful. It sits high to begin with so getting out of it I use the stand option to get my feet almost to the floor. So we can't find anything on getting that seat back adjusted to much higher, it's probably about 18" or 19" Took the seat from about 17 "to a 19," much more comfortable. The cup that slides under the arm came with it, i got everything they got brand new, 2 bags all manuals tools plus her ROHO which feels too tight on the air cause it feels stiff. Do I need to buy a new back plate to get it high enough for my head? Her extra back cushion also too low and doesn't form to me, to get started after perusing wheel chair cushions I opted to go with an ortho pet bed 20x30 5"thick to give me the height to rest my head and neck. Bought a good lumbar pillow but foam blocks to stick in and form the cushion out is full so I can work on that. I've been looking for the original higher back cushion also too short. I'm definitely not complaining just working through the adjustments to fit me for best comfort. My husband has been adjusting the best he can, I found after 2019 the m300 chair changed in it's building and made them for easier to adjust. Would really appreciate a video on back of seat adjustments, even called Mar's mobility cause they also do a lot of video's on adjustments but none on the back of the seat so far. Can you help? Hope all is well for you and friends, it's good to haver a network, that I do not have. Thank you if you can help the 80 year old Sr's get the chair right, I'm so blessed to haver it and I know that. He only charged me $1000 cash and we met halfway to get it to me. Gov had a chair for me about 7 years ago but it had problems and had no idea who to contact, my guy left right after my chair was delivered. Where we live doesn't have a wheel chair store all over like in Fl, so I've been on my own. After watching your video's i set my mind on permobil. m300 it even has the light system with turn signals, a surprise.

Here I thought my pricey charger was a better option than the crappy one they sent with the chair. Maybe I should just use the one they sent. I've never had a problem except my last set of batteries only lasted 9 monyhs. Jazzy Air 2 ftr.

As per your comment: Thank you for sharing!

I got 6.7 miles out of my f3 batteries a few weeks ago. I was pretty disappointed because I was on a short vacation and had to get back to the motel to charge for three hours just to go out to get dinner.

Not surprised at the battery bulging. 30+V is pushing them to their limits and the primary cause of issues I believe. I would charge them at 28.8V at 68F and decrease the voltage by 0.03V for each degree above 68F (ballpark the voltage decrease).

Thanks!

Dan I need some advice. My Quantum Edge is too big to use in parts of my home so I daily use my Itty bitty Pride Go chair that I bought used several years ago. I need new batteries in the Go chair and need them before I open up the battery box. Nowhere can I find what batteries the Go chair uses. Will you please use your resources to help me find the battery type? I think it's the 22NF nut and bolt type but want to be sure before ordering.

Why doesn’t Permobil allow the user set their own per-set seating memory?

I might be getting the Quantum R-Trak which I believe is their latest rear wheel drive chair (previous one was the Rival over 10 years ago). Just wondering if you have heard good things about their R-Trak? One of the shop reps says it's a great chair but I'm not sure. Love your content by the way.

I need help with a used invacare Tdx sp. power wheelchair and a asl head array I keep getting an error code of configuration error press reset on the hand controller and it’s not working together. It was working more it’s not.

I loved watching this. Wonderful community of friends.

I know you generally focus on Permobile but I would like to know if you dabble in invacare because I have a TDX SP that has a switch box cabling short what is part of control box as it's hardwired and not a separate standalone cable the wire has a short but unclear how to fix. eBay has some parts for roughly 40 to 60 dollars however dealer numotion wants to charge $3,000 for suggested MSRP. There should be something against charging that much for a single part especially just for a bad wire. But it shuts off all power so I have to do something. Was out running it and thankfully I had somebody with me because when it went bad there was no notice chair completely shut off would not power back on but noticed wiggling the wires what causes you intermittently fash to life. Oddly enough my permobile has the same issue and it's due to I think the chargers overheating the remote socket getting all the way back to the 2.5M 89.5 R-net cable causing a short or break. Because the charger socket jacket getting hot damaging remote in both chairs possible top left pin but then after socket damage doesn't matter what charger you plug up to it they too will overheat not sure why. It's the new style chargers that you spoke about in another video but the problem is supposedly was supposed to be fixed.

i have a 0808 ERROR code, it reffers to a joystick error, MID REFERENCE ERROR, what should i do ?

8:38:14 kino

excellent dan... thoroughly enjoyed watching from start to finish and congrats to the team placing 4th. looking fwd to the livestream and dont forget to take it easy the next few days. c ya 2morrow